Automotive Tool Rental
Winch 12000 lb Capacity
Recover a stuck vehicle, haul timber or load a boat with this powerful auto winch. The series-wound motor stays cool while the 3-stage planetary gear system provides fast line speed. Featuring an automatic load-holding brake for safety. Battery included. Remote included. 2" Receiver Mount included. Heavy Duty D- Ring Mount available for off vehicle use. Available for rental add on for our trailers too!
Spec Sheet
4 hours $39.00
24 hours $59.00
Spec Sheet
4 hours $39.00
24 hours $59.00
Battery Booster Pack
The dsr114 is ideal for 12v batteries, providing 525 cranking amps and 350 cold cranking amps. Digital display displays internal battery percent of charge. Usb port for powering or recharging portable electronic devices. Unique red on/off power switch helps prevent accidental sparking.
Manual Spec Sheet
4 hours $18.00
24 hours $26.00
Manual Spec Sheet
4 hours $18.00
24 hours $26.00
Battery Tester
- Tests 6V and 12V battery voltage, battery cranking and battery charging volts. Features heavy-duty copper plated clamps, 100A load capacity and load safety switch to prevent arcing.
24 hours $7.00
Battery Charger and Booster
Schumacher Electric SC1667 250-Amp 6-Volt/12-Volt Timer-Controlled Battery Charger and Jump Starter. This charger boasts a 135-minute timer, charge rate selector, and built-in ammeter. With a robust 250 cranking Amp (12-Volt) engine start, it's ready to jump-start cars, SUVs, trucks, RVs, and more. Featuring three boost modes (50-Amp 12-Volt, 25-Amp 6-Volt, and 25-Amp 12-Volt), it swiftly rejuvenates deeply discharged batteries, while the 10-Amp 12-Volt charge mode caters to basic charging needs. Compatible with standard, AGM, and gel batteries.
Manual Operating Instructions
Spec Sheet
4 hours $10.00
24 hours $19.50
Manual Operating Instructions
Spec Sheet
4 hours $10.00
24 hours $19.50
Cooling System Pressure Tester
Detects and exposes external system leaks. Detects internal engine leaks due to blown gaskets or cracked block. Vacuum type cooling system. Purge and refill for quick change of coolant. Test Range: 0 – 35 psi. Includes hand pump and adapters to fit most popular domestic and import cars and trucks.
Instructions
Video
4 hours $9.00
24 hours $15.50
Instructions
Video
4 hours $9.00
24 hours $15.50
Automotive Borescope
- Three cameras are built into the end of this camera's probe for a wider combined field of view. One button quickly toggles between the front-facing camera & both side-view cameras for a combined 234° field of view. This hand-held inspection camera is ergonomic to use, including a 5" IPS color screen provides a clearer & broader view of the visuals provided from the camera probe. This endoscope camera can be used for mechanical inspection, car repair, electrical installs, house DIY, wall upgrades, chimney cleaning, HVAC maintenance, and more. Includes 15 ft or 50 ft cable.
- Manual Spec Sheet
4 hours $15.00
24 hours $25.00
Body Repair Kit "Hydro" Port-a-Power
The Big Red 10-Ton Porta Power with Wheel Case is a convenient kit for heavy lifting in auto body, frame repair and other work. It lifts as high as 18-1/2 in. Snap lock design for fast and easy assembly. Automatic pump overload system prevents ram and equipment damage. Durable heavy walled extension tubes for long service life. Flex head features permanently molded interlocked rubber pad to prevent separation.
Manual
2 hours $19.00
4 hours $29.00
24 hours $59.00
Manual
2 hours $19.00
4 hours $29.00
24 hours $59.00
Vibratory Tumbler for Metal
This heavy duty 18 lb. vibratory bowl can be used wet or dry. The vibratory action produces quicker results compared to a rotary tumbler. The bowl rests on rubber mounted feet for added stability when operating. The drum opening is 10-1/2 in. in diameter to easily add and remove items. Recommended media includes plastic beads, walnut shell, corn cob, red rouge and ruby powder.
Resin media for rust removal without damaging threads included with rental.
Manual
4 hours $15.00
24 hours $29.00
Resin media for rust removal without damaging threads included with rental.
Manual
4 hours $15.00
24 hours $29.00
Ultrasonic Cleaner 30 Liter
The Ultrasonic Cleaner works well for cleaning a variety of items, including automotive parts, and jewelry. It has a 40kHz frequency, and heated 30L tank. The heated tank can be set up to 176 degrees F. Degas mode available for cleaning solvents. Parts basket is included with stainless steel 30 L tank for easy part removal and clean up. Cleaning solution not included. Can be used with water or a variety of commercially available cleaners. White Bear Rental is not responsible for damage caused to items by use of non-approved solvents or cleaning solutions.
Manual Operation Guide
Video Spec Sheet
4 hours $15.00
24 hours $29.00
Manual Operation Guide
Video Spec Sheet
4 hours $15.00
24 hours $29.00
Socket Set Metric 19-50mm 3/4" Drive - Large
The socket set includes a steel ratchet and a sturdy storage case for organization and transport. The set includes:
12-point cold-forged, chrome-plated sockets
19mm, 22mm, 24mm, 26mm, 27mm, 28mm, 30mm, 32mm, 34mm, 36mm, 38mm, 41mm, 42mm, 45mm, 48mm, 50mm
19-1/2" heat-treated steel ratchet
19-1/2" flex breaker bar
4" and 8" extensions
4 hours $10.00
24 hours $19.00
12-point cold-forged, chrome-plated sockets
19mm, 22mm, 24mm, 26mm, 27mm, 28mm, 30mm, 32mm, 34mm, 36mm, 38mm, 41mm, 42mm, 45mm, 48mm, 50mm
19-1/2" heat-treated steel ratchet
19-1/2" flex breaker bar
4" and 8" extensions
4 hours $10.00
24 hours $19.00
Ratchet Set SAE 7/8"-2" 3/4" Drive - Large
The socket set includes a steel ratchet and a sturdy storage case for organization and transport. The set includes:
12-point cold-forged, chrome-plated sockets
7/8", 15/16", 1", 1-1/16", 1-1/8", 1-3/16", 1-1/4", 1-5/16", 1-3/8", 1-7/16", 1-1/2", 1-5/8", 1-3/4", 1-13/16", 1-7/8", 2"
19-1/2" heat-treated steel ratchet
19-1/2" flex breaker bar
4" and 8" extensions
4 hours $10.00
24 hours $19.00
12-point cold-forged, chrome-plated sockets
7/8", 15/16", 1", 1-1/16", 1-1/8", 1-3/16", 1-1/4", 1-5/16", 1-3/8", 1-7/16", 1-1/2", 1-5/8", 1-3/4", 1-13/16", 1-7/8", 2"
19-1/2" heat-treated steel ratchet
19-1/2" flex breaker bar
4" and 8" extensions
4 hours $10.00
24 hours $19.00
Socket Set SAE 1 5/8"-3 1/8" 1" Drive - Jumbo
The socket set includes a steel ratchet and a sturdy storage case for organization and transport. The set includes:
12-point cold-forged, chrome-plated sockets
1-5/8", 1-11/16", 1-3/4", 1-13/16", 1-7/8", 2", 2-1/8", 2-3/16", 2-1/4", 2-3/8", 2-1/2", 2-5/8", 2-3/4", 2-15/16", 3", 3-1/8"
26" heat-treated steel ratchet
22" Sliding T-Bar
8" and 18" extensions
4 hours $15.00
24 hours $29.00
12-point cold-forged, chrome-plated sockets
1-5/8", 1-11/16", 1-3/4", 1-13/16", 1-7/8", 2", 2-1/8", 2-3/16", 2-1/4", 2-3/8", 2-1/2", 2-5/8", 2-3/4", 2-15/16", 3", 3-1/8"
26" heat-treated steel ratchet
22" Sliding T-Bar
8" and 18" extensions
4 hours $15.00
24 hours $29.00
Cylinder Compression Test Kit
Featuring compression hold and release functions, whether you’re working on valves or want to test long term performance, it delivers and packed in a protective blow molded case, it travels fast when duty calls. This compression test kit’s wide range of fittings ensure it’s the right size for your spark plug seat, while an array of quick connectors swaps between cylinders quickly, for accurate whole engine testing. A solid tool, built to give you accurate readings up to 300PSI and 20 KPa, add this compression tester to your kit and get the job done right.
Manual Video
4 Hours $8.00
24 hours $12.00
Manual Video
4 Hours $8.00
24 hours $12.00
Engine Hoist - Breakdown
The Breakdown Engine Hoist can be quickly taken apart, moved and assembled. They go wherever the job is — backyard, shop, warehouse, office tower or construction site. Works best for car engines. 1500 lbs Capacity.
Spec Diagram
Manual
4 hours $25.00
24 hours $39.00
Spec Diagram
Manual
4 hours $25.00
24 hours $39.00
Engine Hoist - Towable
The Towable Engine Hoist is perfect for situations where long reach and high lift are required. Boom hooks can be raised to a full 10 feet, making it the ideal lift for larger vehicles and boat. The unique gooseneck design lets users reach into engine compartments without touching the surrounding structure. 2" ball. 2000 lbs Capacity.
Spec Diagram
Manual
4 hours $35.00
24 hours $49.00
Spec Diagram
Manual
4 hours $35.00
24 hours $49.00
Engine Hoist Sling
This universal Engine Hoist Sling makes engine handling and positioning easier. Great for use with engine hoists or engine cranes. The swivel handle allows for easy adjusting. 1,500-lb. working load.
Manual
4 hours $5.50
24 hours $9.00
Manual
4 hours $5.50
24 hours $9.00
Chain Sling Adjustable
Made from Grade 100 alloy steel chain, alloy steel master link and two sling hooks. All Adjust-A-Link Slings are factory tested and OSHA certified. 9/32" Chain. 10' Long.
Spec Sheet
4 hours $5.50
24 hours $9.00
Spec Sheet
4 hours $5.50
24 hours $9.00
Engine Stand
This 1000 lb. Capacity Engine Stand is ideal for engine repairs that can’t be completed while the engine block is in the vehicle. This engine stand provides a sturdy support structure to secure the engine outside of the vehicle. Use an engine hoist or crane to remove the engine from the vehicle, then mount it to the faceplate on this engine stand.
Fully adjustable engine support rotates 360º and locks in place
Four adjustable arms for easy engine block mounting
24 hours $15.00
Fully adjustable engine support rotates 360º and locks in place
Four adjustable arms for easy engine block mounting
24 hours $15.00
Floor Jack - 2 Ton Hydraulic
This 2 Ton Low-Profile Service Floor Jack reaches lifting points more easily under low-clearance vehicles. The dual piston pump provides quick lifting, reaching working height in 3-1/2 pumps.
4 hours $15.00
24 hours $22.00
4 hours $15.00
24 hours $22.00
Floor Jack - 4 Ton Hydraulic
This 4 Ton Professional Low-Profile Service Floor Jack reaches lifting points more easily under low-clearance vehicles. The dual piston pump provides quick lifting, reaching working height in 3-1/2 pumps.
Manual Spec Sheet
4 hours $19.00
24 hours $27.00
Manual Spec Sheet
4 hours $19.00
24 hours $27.00
Jack Stand 6 Ton
Capacity: 6 Tons; Lifting Range: 15.75" to 24"; Steel base with four feet pads for stability; Ratchet action design with ductile iron support column.
Price Each
4 hours $5.00
24 hours $7.50
Price Each
4 hours $5.00
24 hours $7.50
Transmission Jack
1000 lb capacity. Chains and brackets not included.
4 hours $19.00
24 hours $29.00
4 hours $19.00
24 hours $29.00
Impact Wrench - 3/4" Electric
Adapter for 1/2" available
4 hours $17.00
24 hours $29.00
4 hours $17.00
24 hours $29.00
Ball Joint Press 3 in 1
Contains press, 3 receiver tubes, installation, and removal adapters.
Instructions
4 hours $17.00
24 hours $29.50
Instructions
4 hours $17.00
24 hours $29.50
4WD Spindle Nut Socket - Ford - GM
Axle Nut Socket - Metric
CTA Model 4220 4222 4225
For removing and installing front hub/axle nuts. 1/2" square drive.
4220 30mm, 4222 32mm, 4225 36mm
4 hours $4.00
24 hours $8.50
For removing and installing front hub/axle nuts. 1/2" square drive.
4220 30mm, 4222 32mm, 4225 36mm
4 hours $4.00
24 hours $8.50
Bearing Puller
CTA Model 8070 Removes fly wheel pilot bearings and bushings up to 7-1/2" (190mm) long. Better than slide hammer type when working in tight areas. Better control for precision pulling.
Standard Range - 1/2" to 1-1/2" (13mm to 38mm I.D.)
Instructions
4 hours $7.50
24 hours $9.75
Standard Range - 1/2" to 1-1/2" (13mm to 38mm I.D.)
Instructions
4 hours $7.50
24 hours $9.75
Bearing Splitter / Separator
CTA Model 8060 8065 Remove generator gears, bearings, bearing cones and similar parts where ordinary puller jaws will not reach. Knife-like edges minimize damage to parts.
8060 Range: Up to 2-1/4" (57mm)
8065 Range: Up to 4-1/4" (108mm)
Instructions
4 hours $7.50
24 hours $9.75
8060 Range: Up to 2-1/4" (57mm)
8065 Range: Up to 4-1/4" (108mm)
Instructions
4 hours $7.50
24 hours $9.75
Coil Spring Compressor
CTA Model 4030 Removes, installs, and compresses coil springs that can be reached through the center of the coil. Features Acme threaded rod and forged, heat-treated alloy hooks. Works on coil springs up to ¾” diameter.
Instructions
4 hours $7.50
24 hours $10.00
Instructions
4 hours $7.50
24 hours $10.00
Clutch Alignment Tool
CTA Model 6125 For fast easy alignment of clutch plates on most domestic and import cars.
Bushing Range:
Import: 12 to 12.7 mm, 15.8 to 16 mm, 17.4 to 18 mm, 21 to 22.2 mm.
Domestic: 0.561 to 0.590", 0.749 to 0.787", 0.812 to 0.874", 0.984 to 1.181"
4 hours $7.00
24 hours $10.00
Bushing Range:
Import: 12 to 12.7 mm, 15.8 to 16 mm, 17.4 to 18 mm, 21 to 22.2 mm.
Domestic: 0.561 to 0.590", 0.749 to 0.787", 0.812 to 0.874", 0.984 to 1.181"
4 hours $7.00
24 hours $10.00
CV Joint Puller
CTA Model 4245. Pulls CV joints with hidden retaining rings without damaging the roller bearing inside the joint. Use with CTA #4310 Axle Puller. 5/8" - 18 threaded hole. 17/8" (48mm) wide opening.
4 hours $7.00
24 hours $10.00
4 hours $7.00
24 hours $10.00
CV Joint Boot Clamp Pliers - Eared
CTA Model 4210 Use to easily service ear style clamps on axle boots/hoses. Clamps are often difficult to properly tighten and securer without the correct tool.
Tool features 1/2" drives for use with torque wrench when tightening clamps
OAL: 11-1/2" / 29cm
24 hours $4.00
Tool features 1/2" drives for use with torque wrench when tightening clamps
OAL: 11-1/2" / 29cm
24 hours $4.00
Gear Puller 2 or 3 Jaw - 3"-7"
Gear Puller 2 or 3 Jaw - 4"-11"
Harmonic Balancer Installer
CTA Model 2238
Installs harmonic balancer or drive pulleys that are pressed on the camshaft
Includes 8 adapters:M16-2.0, M14- 1.5, M12-1.5, 3/4-16, 5/8-18, 9/16-18, 1/2–20, 7/16-20
4 hours $7.00
24 hours $10.00
Installs harmonic balancer or drive pulleys that are pressed on the camshaft
Includes 8 adapters:M16-2.0, M14- 1.5, M12-1.5, 3/4-16, 5/8-18, 9/16-18, 1/2–20, 7/16-20
4 hours $7.00
24 hours $10.00
Harmonic Balancer Puller
CTA Model 2236
Includes: Yoke, 71/2” (19cm) center screw, Flat & Pointed adapter tips, 4 bolt sizes:, (3) M8 x 1.25 x 80mm, (2) 3/8”–16 x 4”, (3) 3/8”–24 x 2”, (3) 5/16”–18 x 2”
4 hours $7.00
24 hours $10.00
Includes: Yoke, 71/2” (19cm) center screw, Flat & Pointed adapter tips, 4 bolt sizes:, (3) M8 x 1.25 x 80mm, (2) 3/8”–16 x 4”, (3) 3/8”–24 x 2”, (3) 5/16”–18 x 2”
4 hours $7.00
24 hours $10.00
MacPherson Spring Compressor
CTA Model 4035 or 4036
Removes and installs coil springs where removal through the center of the spring is not possible. Services both Straight & Curved Coil Springs. Includes S-bolts & wing nuts. Maximum diameter spring that the hooks will accommodate is 0.75". Diameter of the rod: 5/8".
Instructions
4 hours $9.00
24 hours $14.50
Removes and installs coil springs where removal through the center of the spring is not possible. Services both Straight & Curved Coil Springs. Includes S-bolts & wing nuts. Maximum diameter spring that the hooks will accommodate is 0.75". Diameter of the rod: 5/8".
Instructions
4 hours $9.00
24 hours $14.50
Pickle Fork
CTA 4010 and 4015
Separates ball joints from the steering knuckle making replacement and disassembly of front suspensions easy. Prevents damage to suspension and steering components.
Opening: 1" and 0.75" OAL: 12"
24 hours $8.00
Separates ball joints from the steering knuckle making replacement and disassembly of front suspensions easy. Prevents damage to suspension and steering components.
Opening: 1" and 0.75" OAL: 12"
24 hours $8.00
Pilot Bearing puller, Slide Hammer
CTA Model 8075
For inside pulling jobs, jaws will remove flywheel pilot and other bearings.
Range: 1/2" to 1-1/2" (13mm to 38mm).
Instructions
4 hours $7.00
24 hours $10.00
For inside pulling jobs, jaws will remove flywheel pilot and other bearings.
Range: 1/2" to 1-1/2" (13mm to 38mm).
Instructions
4 hours $7.00
24 hours $10.00
Body Dent Puller, Slide Hammer
CTA Model 5115
Used for dent removal in body work.
4 hours $7.00
24 hours $10.00
Used for dent removal in body work.
4 hours $7.00
24 hours $10.00
Pittman Puller
CTA Model 4020
Removes the pitman arm from most vehicles. Center screw with pointed tip and 3/4" hex head. Opening: 1-5/16" / 33mm. Depth: 2-1/2 / 64mm.
CTA # 4025 (small) also available
Instructions
4 hours $7.00
24 hours $10.00
Removes the pitman arm from most vehicles. Center screw with pointed tip and 3/4" hex head. Opening: 1-5/16" / 33mm. Depth: 2-1/2 / 64mm.
CTA # 4025 (small) also available
Instructions
4 hours $7.00
24 hours $10.00
Power Steering Pump / Alternator Pulley Puller
CTA Model number 8080
Removes pressed-on 1 or 2 groove pulleys from alternators and power steering pumps without damage. Fits both large and small pulleys found on older domestic and import passenger cars. Features rigid, drop-forged jaws, a solid block body and a fine thread screw for easy pulling.
Instructions
4 hours $6.00
24 hours $8.00
Removes pressed-on 1 or 2 groove pulleys from alternators and power steering pumps without damage. Fits both large and small pulleys found on older domestic and import passenger cars. Features rigid, drop-forged jaws, a solid block body and a fine thread screw for easy pulling.
Instructions
4 hours $6.00
24 hours $8.00
Power Steering Pump Installer
CTA Model 8085
Used to install power steering pump without damaging it. Fits most models.
4 hours $6.00
24 hours $8.00
Used to install power steering pump without damaging it. Fits most models.
4 hours $6.00
24 hours $8.00
Ridge Reamer
CTA Model 2212 Heavy-Duty Ridge Reamer is designed to remove ridges from the top of the cylinder to achieve a smooth wall surface on engine bores from 3 – 5-Inch / 76 – 127-Millimeter. This tool works on canted and short stroke types. The tungsten-carbide blade is reversible for a long life. The reamer can be set to change from one cylinder to another without readjusting.
4 hours $8.00
24 hours $12.00
4 hours $8.00
24 hours $12.00
Piston Ring Groove Cleaner
CTA Model 2032 Comes with Two Easy-To-Set Cutter Wheels for Quick Cleaning of Grooves. Heavy coil spring holds cutter in groove for fast removal of carbon. Tool comes with standard 24020 cutter blade sizes: 5/64", 3/32", 1/8", 5/32", 3/16" and special 24350 cutter blade with sizes: 1.5mm, 1/16", 1.75mm, 2mm, and 1/4". Handles pistons 2 3/4" to 5" diameter.
4 hours $8.00
24 hours $12.00
4 hours $8.00
24 hours $12.00
Engine Cylinder Hone
CTA Model 2300 2310 Resurface cylinder walls so new rings will seat. Eliminate minor cylinder wall imperfections. Adjustable diameter and tension settings. Flex shaft will fit variable speed drill. Medium grit (220) stones
2300 Range: 32 - 89mm. Stone Length: 2" / 51mm
2310 Range: 51 - 178mm. Stone Length: 4" / 102mm
4 hours $8.00
24 hours $12.00
2300 Range: 32 - 89mm. Stone Length: 2" / 51mm
2310 Range: 51 - 178mm. Stone Length: 4" / 102mm
4 hours $8.00
24 hours $12.00
Piston Ring Compressor Large
Adjustable friction brake and dimpled bottom edge to keep tool from slipping into cylinder.
4 hours $7.00
24 hours $9.00
4 hours $7.00
24 hours $9.00
Piston Ring Compressor Small
CTA Model 2027
Adjustable friction brake and dimpled bottom edge to keep tool from slipping into cylinder.
4 hours $7.00
24 hours $9.00
Adjustable friction brake and dimpled bottom edge to keep tool from slipping into cylinder.
4 hours $7.00
24 hours $9.00
Slide Hammer Set - Axle Puller
CTA 4310
Flange Type Axle Puller is designed to work on most cars and light trucks. It can be used as a wheel puller with either, CTA Tools 4245 CV Joint Puller or CTA Tools 4300 Front Wheel Hub Puller.
4 hours $9.00
24 hours $15.50
Flange Type Axle Puller is designed to work on most cars and light trucks. It can be used as a wheel puller with either, CTA Tools 4245 CV Joint Puller or CTA Tools 4300 Front Wheel Hub Puller.
4 hours $9.00
24 hours $15.50
Slide Hammer Set - 4 Jaw Set
CTA Model 8090
Remove bearings, gears, bushings, seals, grease retainers, etc.
Includes 4 jaw assemblies for internal/external and 2/3 jaw pulling
3 jaw range: 1-1/2" to 4-1/2" (38mm to 114mm) outside, 1-5/16" to 4-3/4" (33mm to 121mm) inside
2 jaw range: 1" to 4-1/2" (25mm to 114mm) outside, 1-1/4" to 3-3/8" (32mm to 86mm) inside
4 hours $9.00
24 hours $15.50
Remove bearings, gears, bushings, seals, grease retainers, etc.
Includes 4 jaw assemblies for internal/external and 2/3 jaw pulling
3 jaw range: 1-1/2" to 4-1/2" (38mm to 114mm) outside, 1-5/16" to 4-3/4" (33mm to 121mm) inside
2 jaw range: 1" to 4-1/2" (25mm to 114mm) outside, 1-1/4" to 3-3/8" (32mm to 86mm) inside
4 hours $9.00
24 hours $15.50
Steering Wheel Puller
CTA Model 1515 A must for removing the steering wheel for the replacement or to repair the directional signal switch, horn contacts, etc.. Will not damage steering wheel or column. Includes: 5 sets of side bolts: 5/16"-18, 5/16"-24, 3/8"-16, 1/4"-28 & 8mm-1.25. Yoke and center screw with pointed/removable adapter.
Instructions
4 hours $7.50
24 hours $10.00
Instructions
4 hours $7.50
24 hours $10.00
Steering Wheel Lock Plate Remover/Installer Tool
CTA Model 1504
Adapter flips to fit both 9/16" - 18 and 14mm threads to service tilt-wheel and telescoping columns. Narrow yoke is 5" (127mm) deep.
4 hours $7.50
24 hours $10.00
Adapter flips to fit both 9/16" - 18 and 14mm threads to service tilt-wheel and telescoping columns. Narrow yoke is 5" (127mm) deep.
4 hours $7.50
24 hours $10.00
Tail Pipe Cutter
CTA Tools 2631 Tailpipe Cutter is designed to cut pipes with an outer diameter of 3/4-inch to 3-Inch (19-milimeters to 76-millimeters). This cutter features carbide cutting wheels with spacers for superior tracking.
4 hours $7.50
24 hours $10.00
4 hours $7.50
24 hours $10.00
Tail Pipe Expander
CTA Model 2622 2624 For flaring and expanding tailpipes.
2622 Range: 1-1/2 to 2-1/2" / 38 to 64mm I.D.
2624 Range: 2-1/8 to 3-1/2" / 54 to 89mm I.D.
Instructions
4 hours $9.00
24 hours $15.50
2622 Range: 1-1/2 to 2-1/2" / 38 to 64mm I.D.
2624 Range: 2-1/8 to 3-1/2" / 54 to 89mm I.D.
Instructions
4 hours $9.00
24 hours $15.50
Torque Wrench 3/8 Drive - In/lbs
The Craftsman 9-31423 3/8" Torque Wrench 25-250 in.lbs is accurate to +/- 4%.
Manual
4 hours $9.00
24 hours $19.00
Manual
4 hours $9.00
24 hours $19.00
Torque Wrench, 1/2" Drive - Ft/lbs
The Craftsman 44595 1/2" Torque Wrench 20-150 ft.lbs is accurate to +/- 4%. Adapter to 3/8" drive available.
Manual
4 hours $9.00
24 hours $19.00
Manual
4 hours $9.00
24 hours $19.00
Valve Spring Compressor
CTA Model 2233 Fits Most OHV and L-Head Automotive Engines Works on Valves as Short as 3.5-Inch (89-Millimeter) and Valve Spring Retainers Down to 7/8-Inch (22-Millimeter) in Diameter Compressor is 7-Inch (18-Centimeter) at the Opening and 5-Inch (13-Centimeter) in Depth Rack and Pinion Design Compresses Valve Springs Easily Includes Both, Offset and Straight Adjusting Jaws
4 hours $9.00
24 hours $12.50
4 hours $9.00
24 hours $12.50
Oil Extractor - 6.25 Gallon
The 6-1/4 gallon oil extractor extracts fluids through dipstick tubes as well as other openings. Minimize clean up when working with cars, tractors, boats, small aircraft engines, industrial gear boxes, coolant and hydraulic systems. The device has a 1/2 gallon per minute extraction rate and comes with vacuum gauges and 5 probes.
Tank reservoir size: 6-1/4 gallons
Suction capacity: 4-1/4 gallons
Air inlet: 1/4" NPT
Working air pressure: 70-110 PSI
Oil temperature range: 68-158 degrees F
User manual
4 hours $17.00
24 hours $26.00
Tank reservoir size: 6-1/4 gallons
Suction capacity: 4-1/4 gallons
Air inlet: 1/4" NPT
Working air pressure: 70-110 PSI
Oil temperature range: 68-158 degrees F
User manual
4 hours $17.00
24 hours $26.00
Tire Inflator with Digital Gauge
Three function handle checks tire pressure, releases pressure (if needed), or inflates tire. 23” Inflator hose ideal for use on larger tires.
Accuracy: 2 - 110 psi (±2 psi), 111+ psi (±3 psi)
Large 2.6” gauge with 360° swivel for ease of viewing from any position
Straight-on locking chuck
Range: 2 -170 psi (11 bar, 1100 kpa)
4 hours $5.00
24 hours $10.00
Accuracy: 2 - 110 psi (±2 psi), 111+ psi (±3 psi)
Large 2.6” gauge with 360° swivel for ease of viewing from any position
Straight-on locking chuck
Range: 2 -170 psi (11 bar, 1100 kpa)
4 hours $5.00
24 hours $10.00
Creeper
Full length padded cushion and headrest for comfort
Foldaway design for easy storage
Oil-resistant casters
4 hours $4.00
24 hours $7.00
Foldaway design for easy storage
Oil-resistant casters
4 hours $4.00
24 hours $7.00